Opens in a new tab

Medium-Voltage Diesel Generators Explained: Principles, Benefits, and System Options

Illustration: Medium-Voltage Diesel Generators Explained: Principles, Benefits, and System Options

How voltage choice affects distribution, equipment, and operation at large facilities

For a large data center, selecting backup power means deciding how much generating capacity is needed, how it will connect to the electrical network, and how the facility will stay supplied during maintenance or a fault.

Medium-voltage diesel generation reduces feeder current compared with low-voltage generation at the same power and power factor. This can simplify distribution across a large site, but the overall benefit depends on cable distances, the existing network, and the equipment needed to connect and operate the plant.

An uninterruptible power supply (UPS) typically keeps connected IT loads running while the generators start and the facility transfers to generator power. The output voltage needs to suit this entire supply arrangement.

What makes a generator medium voltage?

Medium-voltage (MV) generator sets produce electricity at voltages used in industrial distribution, such as 6.6, 10, 10.5, 11, and 13.8 kV. Voltage classifications vary by market and equipment convention, so specifications should always state the actual output voltage.

A generator set consists of a diesel engine, an alternator, controls, and supporting equipment. The engine supplies mechanical power. The alternator’s design establishes its voltage rating, while its excitation system regulates the output voltage.

Power and voltage are separate specifications. Low-voltage (LV) generator sets are available at multi-megawatt ratings; an MV output does not, by itself, indicate a higher power rating. Caterpillar’s C175-20 product family, for example, lists several power ratings and a voltage range from 480 V to 13.8 kV. The required combination must be confirmed for the selected configuration. Caterpillar C175-20 specifications

From diesel fuel to electrical power

The operating principle is the same for low- and medium-voltage sets. Combustion in the engine produces mechanical rotation, which drives an alternator to generate electrical power.

In a four-stroke diesel engine, the cycle proceeds through intake, compression, power, and exhaust. Air enters the cylinder during intake. The piston then compresses it, raising its temperature. Fuel is injected near the end of compression and ignites in the hot air. Combustion pressure drives the piston downward, and the exhaust stroke clears the cylinder for the next cycle.

Figure 1. Four stages of the same cylinder’s cycle. The panels illustrate successive strokes, not the firing order of four different cylinders.

A turbocharger uses energy in the exhaust to drive a compressor that supplies more intake air. Fuel-injection equipment controls fuel delivery and combustion. Common-rail injection and four-valve cylinder heads are features of particular engine designs; neither is determined by the alternator’s output voltage.

The engine’s crankshaft drives the alternator rotor, whose rotating magnetic field induces voltage in the stator windings. The automatic voltage regulator (AVR) adjusts excitation to maintain the output voltage.

Brushless alternators and excitation systems powered by a permanent magnet generator (PMG) are available across voltage categories. STAMFORD | AvK’s PG80 manual, for example, describes brushless, PMG-excited alternators in multiple voltage ranges. STAMFORD | AvK PG80 manual

An MV alternator requires insulation, terminals, and clearances appropriate to its electrical stresses. Voltage withstand capability and insulation thermal class describe different properties; both belong in the equipment specification.

Why higher voltage reduces current

For a balanced three-phase system, real power is:

P = √3 × V × I × PF

P is real power in watts, V is line-to-line voltage in volts, I is line current in amperes, and PF is power factor. At the same real power and power factor, current falls as voltage rises.

For an illustrative 2 MW load at a power factor of 0.8:

At 10 kV, current is one twenty-fifth of the 400 V value. Calculating the resulting reduction in losses requires a comparison of the actual installations.

Resistive loss in a conductor is I²R, where R is its resistance. Cable losses therefore depend on conductor size, material, length, and the number of parallel runs. Compare the proposed cable arrangements and include transformer and other equipment losses when assessing total system efficiency.

Compare the distribution options

Three arrangements are worth distinguishing:

Figure 2. Direct MV generation can remove the generator-side step-up transformer. LV loads downstream still require suitable voltage transformation and distribution.

Direct MV generation may reduce the equipment needed between the generator and an existing MV bus. It can also avoid long, high-current LV connections. Those savings must be weighed against the MV equipment and installation costs.

Select the voltage to fit the site’s distribution network, equipment availability, fault levels, and future expansion. Depending on those requirements, a larger campus may use several distribution voltages or divide its load into separate blocks.

Protection and control are part of the generator system

The alternator connects to the distribution system through circuit breakers and switchgear. Current and voltage transformers provide measurements for metering, protection, and synchronization. Protective relays detect specified faults and initiate the required response.

The grounding arrangement must be designed for the network. Resistance grounding is one option used in MV systems, but the appropriate arrangement depends on fault-current requirements, protection coordination, and system topology. Differential protection detects faults within a defined protection zone and can be used at different voltage levels. Cummins paralleling application manual

Before a generator connects to an energized bus, its phase sequence must match the bus, and the voltage difference, frequency difference, and phase-angle difference must be within the permitted synchronization limits. Once connected, controls manage real- and reactive-power sharing. The control and protection design is central to reliable parallel operation.

Control power, batteries, communications, and the ability to isolate equipment for maintenance deserve the same attention as the main power circuit. These supporting systems can affect whether healthy generators remain available during an abnormal event.

Separate voltage choice from other equipment choices

Engine speed, operating rating, and packaging describe different aspects of the equipment.

Select the operating rating for the expected running hours and load profile. Standby, prime, and continuous ratings describe different duties; a standby rating is not an unlimited continuous-duty rating. Engine speed is a separate choice that affects the engine and alternator arrangement, regardless of output voltage.

Generator sets may be supplied as open units, in sound-attenuated enclosures, or in containerized packages. Compare each proposed package together with its ventilation, cooling, exhaust, noise-control, transport, and service-access requirements.

Specify the standards that apply to each part of the system. ISO 8528 addresses generator sets, while IEC 60034 addresses rotating electrical machines. IEC 60034-1:2026 covers machine rating and performance. Project specifications should identify the applicable parts, editions, and acceptance criteria. IEC 60034-1

For project discussions with LETON POWER, start with the required net output, site conditions, load sequence, and reliability objectives. Compare voltage options against those same requirements, including the distribution equipment, installation cost, and maintenance needs.

keep the world powered

Table of contents

Emergency diesel generators during a lightning storm power outage

FLASH OFFER • LIMITED STOCK

Claim Your 5% Instant Quote Discount!

Request a free quote now and get:
✓ 24/7 Technical Support Guarantee
✓ Customized Load Analysis (Value: $500)

Contact Us

We're here to help. Complete the form below to receive assistance.